Russia
Manufacturer/ Producer
Russia
Rubber speed bump is a product manufactured by our company for many years. As a manufacturer, we understand the full degree of responsibility, and offer balanced and thoughtful solutions to ensure road safety. Thanks to many years of experience, we have managed to develop a high-quality product with high performance properties. Our products are made from a wear-resistant rubber compound used in the tire industry, which guarantees a long service life. Leading companies in the field of road maintenance and improvement trust the quality of our products. IDN-500 has 6 holes reinforced with washers for mounting. The road roughness is set using anchor bolts with a diameter of 10 mm.
Request for a quoteRussia
Rubber speed bump is a product manufactured by our company for many years. As a manufacturer, we understand the full degree of responsibility, and offer balanced and thoughtful solutions to ensure road safety. Thanks to many years of experience, we have managed to develop a high-quality product with high performance properties. Our products are made from a wear-resistant rubber compound used in the tire industry, which guarantees a long service life. Leading companies in the field of road maintenance and improvement trust the quality of our products. IDN-500 - end - this is an end element for a speed bump with a width of 500 mm. It is attached to anchor bolts. On top, it has a kind of spherical "spikes" for better adhesion of the car wheel.
Request for a quoteRussia
Rubber speed bump is a product manufactured by our company for many years. As a manufacturer, we understand the full degree of responsibility, and offer balanced and thoughtful solutions to ensure road safety. Thanks to many years of experience, we have managed to develop a high-quality product with high performance properties. Our products are made from a wear-resistant rubber compound used in the tire industry, which guarantees a long service life. Leading companies in the field of road maintenance and improvement trust the quality of our products. IDN-900 - end - this is the largest type of elements in the line of artificial road bumps. It provides the safest passage for vehicles by creating a long and smooth artificial roughness on the road surface. Has 12 holes reinforced with washers. Anchor bolts with a diameter of 10 mm are used for fastening. Holes for bolts with a diameter of 11 mm.
Request for a quoteRussia
Rubber speed bump is a product manufactured by our company for many years. As a manufacturer, we understand the full degree of responsibility, and offer balanced and thoughtful solutions to ensure road safety. Thanks to many years of experience, we have managed to develop a high-quality product with high performance properties. Our products are made from a wear-resistant rubber compound used in the tire industry, which guarantees a long service life. Leading companies in the field of road maintenance and improvement trust the quality of our products. IDN-900 - end - this is an end element for a speed bump with a width of 900 mm. It is made of black rubber. It is attached to anchor bolts. On top, it has a kind of spherical "spikes" for better adhesion of the car wheel.
Request for a quoteRussia
Rubber crumb with a fraction of 1-3 mm is one of the important components necessary for the manufacture of artificial turf for sports grounds and running tracks, as well as for covering children's and playgrounds. Terms of use: • Temperature of working materials, base surface and environment from +10°С to +40°С. • The crumb rubber should be dry and should not contain rubber dust, textile cord, etc. • The temperature of the binder should range from +15°С to +25°С • The surface temperature of the base should be at least 3°C above the dew point. Use on on damp bases is prohibited; • The surface should be dust-free, degreased, cleaned of contaminants • Exposure to atmospheric precipitation is undesirable during the day after laying the coating Laying technology: The crumb can be used both at manual laying of coverings, and when using automatic stackers.
Request for a quoteRussia
Rubber crumb with a fraction of 2-4 mm is one of the important components necessary for the manufacture of artificial turf for sports grounds and running tracks, as well as for covering children's and playgrounds. Terms of use: • Temperature of working materials, base surface and environment from +10°С to +40°С. • The crumb rubber should be dry and should not contain rubber dust, textile cord, etc. • The temperature of the binder should range from +15°С to +25°С • The surface temperature of the base should be at least 3°C above the dew point. Use on on damp bases is prohibited; • The surface should be dust-free, degreased, cleaned of contaminants • Exposure to atmospheric precipitation is undesirable during the day after laying the coating Laying technology: The crumb can be used both at manual laying of coverings, and when using automatic stackers.
Request for a quoteRussia
Glue-303MS (hereinafter - "the Binder") is a one-component polyurethane binder for elastic elastic permeable coatings based on elastic aggregates (rubber crumb and EPDM-granulate). It does not contain organic solvents. It is cured by air moisture. When cured, it creates an elastic, durable bond with high moisture resistance. Appearance of components Homogeneous transparent colorless or whitish viscous liquid Dynamic viscosity of components at 70°С, Pa s 0.6-0.9 Content of non-volatile substances, % 100 Appearance of the cured coating Rough, elastic, permeable to water and its vapors surface. The degree of roughness depends on the fractional composition of the filler. Tensile strength of the cured coating, N/, within 8-10 (GOST 270-75) Elongation at break, %, not less than 350 (GOST 270-75) Coating curing time (at +20°С and 70% relative humidity) 24 hours – pedestrian loads can be provided; 3 – 5 days.
Request for a quoteRussia
The mixture is used for the manufacture of sealing products that are used in the environment of air, water, weak solutions of acids and alkalis with a volume fraction of not more than 20% (except for acetic and nitric acids)
Request for a quoteRussia
VladRTI has workshops for industrial rubber goods and metalworking. Our staff is composed of professional employees who are ready to produce any molded RP and design the most efficient mold for this. In this regard, we are always ready to help you and take care of all the nuances of the production of non-standard molded RP. There are two options for the production of molded RP. - the customer has a mold: 1. Based on the product data, we will calculate production cost. 2. We receive the mold and make a test sample (if the mold is not designed correctly and this leads to additional costs, the price is recalculated). 3. The customer should approve the sample (if the sample does not fit, we get feedback on it and make a new one based on additional input. Price changes are possible). 4. We start production of the batch.
Request for a quoteRussia
VladRTI has workshops for metalworking. Our staff is composed of professional employees who are ready to design the most efficient mold and produce it. In this regard, we are always ready to help you and take care of all the nuances of mold production. There are two mold production options. - the customer has mold drawing: 1. Based on the mold data, we will calculate production cost. 2. After the customer's approval, we start production. 3. The customer receives the finished mold within the agreed term. - the customer only has a drawing or product sample: 1. Based on the product data, we will calculate the mold production cost. 2. After signing the contract, we begin the design of the mold. 3. After the project is approved by the customer, we begin the production of the mold. 4. The customer receives the finished mold within the agreed term.
Request for a quoteManufacturer/ Producer
Dimitrova street, 7a, attic floor, office 4
Sobinsk district
601204 Vladimir Region - Russia
Turkey
The sand molding process offers a wide range of design options while at the same time making it cheaper and faster. With the molding we can flexibly respond to your needs and offer you the most economical solution. We can supply you parts from 0.1 KG up to 15.000 KG individual weight in the procedure forms Our Aluminum Casting Suppliers for Automotive and Aviation are IATF16949 and EN 9100 certified. Great alloy selection High flexibility Low tooling costs Low production costs steel casting cast iron ductile Iron casting Aluminum Sand Casting Low Pressure Casting
Request for a quoteFrance
Since it was founded in 1979 STEEC offers, has been offering the service of machining parts for moulds and dies for all types of industries based on wire spark erosion cutting in particular. Because of this STEEC is recognized for its expertise in this field of activity both in France and in Europe as a whole.
Request for a quoteChina
We are factory for molds and molding products for plastic and metal material
Request for a quoteSlovenia
We offer product design consultations, tool designing, mould manufacturing and mould maintenance and service.
Request for a quoteCreate one request and get multiple quotes form verified suppliers.